Supermicro SuperServer 7047R-TXRF Uživatelský manuál Strana 34
- Strana / 112
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
5-2
SUPERSERVER 7047R-TXRF User's Manual
Unpacking
The serverboard is shipped in antistatic packaging to avoid electrical static
discharge. When unpacking the board, make sure the person handling it is static
protected.
5-2 Connecting Cables
Several cables need to be connected from the chassis to the serverboard. These
include the data cables for the peripherals and control panel and the power cables.
Connecting Data Cables
The cables used to transfer data from the peripheral devices have been carefully
routed to prevent them from blocking the ow of cooling air that moves through
the system from front to back. If you need to disconnect any of these cables, you
should take care to keep them routed as they were originally after reconnecting
them (make sure the red wires connect to the pin 1 locations). The following data
cables (with their locations noted) should be connected. (See the serverboard layout
for connector locations.)
•SATA drive data cables (I-SATA0 ~ SATA7 )
•Control Panel cable (JF1)
Important! Make sure the the cables do not come into contact with the fans.
Connecting Power Cables
The X9DRX+-F has a 24-pin proprietary power supply connector (JPW1) for
connection to the ATX power supply. In addition, there are two 8-pin secondary
power connectors (JPW2, JPW3) that also must be connected to your power supply.
See Section 5-8 for power connector pin denitions.
Connecting the Control Panel
JF1 contains header pins for various front control panel connectors. See Figure 5-1
for the pin locations of the various front control panel buttons and LED indicators.
All JF1 wires have been bundled into a single ribbon cable to simplify this
connection. Make sure the red wire plugs into pin 1 as marked on the board. The
other end connects to the Control Panel PCB board, located just behind the system
status LEDs on the chassis. See below for details and pin descriptions.
- SUPER 1
- About This Manual 3
- Manual Organization 3
- Table of Contents 6
- Chapter 3 System Interface 7
- Chapter 4 System Safety 7
- Chapter 1 9
- Introduction 9
- 1-2 Serverboard Features 10
- 1-3 Server Chassis Features 11
- DMI: LANE 12
- Reversal 12
- 1-4 Contacting Supermicro 13
- Chapter 2 15
- System Setup 15
- 2-3 Preparing for Setup 16
- Warnings and Precautions! 16
- •Allow the hot plug SMicro12 17
- Reliable Ground 18
- Chassis Cover 19
- Chassis Feet 19
- Chassis Cover Lock 19
- Chassis Handle 20
- Inner Rails 20
- Slide into the Inner Rail 21
- Secure to the 21
- Rear of the Rack 21
- Attach to Middle Rail 21
- Installing the Chassis Cover 23
- Chassis Foot 24
- Receptacle 24
- Chassis Screw 24
- Chapter 3 25
- System Interface 25
- 3-2 Control Panel Buttons 26
- 3-3 Control Panel LEDs 26
- Overheat/Fan Fail 27
- Power Fail 27
- 3-4 Drive Carrier LEDs 28
- Chapter 4 29
- System Safety 29
- 4-3 ESD Precautions 31
- 4-4 Operating Precautions 32
- Chapter 5 33
- Advanced Serverboard Setup 33
- •Control Panel cable (JF1) 34
- 5-3 I/O Ports 35
- OPEN 1st 36
- WARNING! 36
- 5-6 Installing Memory 40
- UDIMM Memory Support 42
- RDIMM Memory Support 42
- LRDIMM Memory Support 42
- 5-6 Adding PCI Add-On Cards 43
- 5-7 Serverboard Details 44
- 5-8 Connector Denitions 46
- USB 4, 5, 6,8 48
- Pin # Denition 48
- USB 7, 9 48
- Pin # Denition 48
- VGA Enable/Disable Jumper 53
- Settings 53
- Jumper Setting Denition 53
- Pins 1-2 Enabled 53
- Pins 2-3 Disabled 53
- 5-10 Onboard Indicators 55
- 5-11 SATA Ports 56
- 5-12 Installing Software 57
- Supero Doctor III 58
- Chapter 6 61
- Advanced Chassis Setup 61
- 6-1 Static-Sensitive Devices 62
- 6-2 Control Panel 62
- 6-3 System Cooling 63
- Rear Fan Release 64
- Mid Fan 64
- Release Tab 64
- 6-4 Power Supply 65
- Power Supply Connections 66
- Tower or Rack Conguration 67
- Rotating the Storage Module 68
- Removing a Drive Carrier 70
- Hard Drive 71
- Hard Drive Tray 71
- Adding Peripheral Drives 72
- Drive Tray Handle 73
- Release Button 73
- Drive Tray 74
- SAS/SATA 74
- Chapter 7 75
- 7-2 Main Setup 76
- Boot Features 78
- •Type of CPU 79
- •CPU Signature 79
- •Microcode Patch 79
- Chipset Conguration 84
- North Bridge 84
- Integrated IO Conguration 84
- QPI Conguration 85
- DIMM Conguration 86
- DIMM Information 86
- South Bridge Conguration 88
- SATA Conguration 89
- PCIe/PCI/PnP Conguration 90
- Super IO Conguration 92
- Serial Port 1 Conguration 92
- Serial Port 2 Conguration 92
- Console Redirection Settings 93
- Console Redirection Settings 95
- ACPI Settings 96
- TPM Enable Status 97
- NIC Conguration 98
- •Factory MAC Address 99
- •Alternate MAC Address 99
- 7-5 IPMI 101
- BMC Network Conguration 102
- 7-6 Boot 103
- 7-7 Security 104
- 7-8 Save & Exit 105
- Appendix A 107
- BIOS Error Beep Codes 107
- Appendix B 109
- System Specications 109
Související produkty a manuály pro Barebone serveru Supermicro SuperServer 7047R-TXRF
Barebone serveru Supermicro 188411 Uživatelský manuál
(122 stránky)
(122 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce