Supermicro SuperServer 7047R-TXRF Uživatelský manuál Strana 15
- Strana / 112
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 2: Server Installation
2-1
Chapter 2
System Setup
2-1 Overview
This chapter provides a quick setup checklist to get your SuperServer 7047R-TXRF
server up and running. Following the steps in the order given should enable you
to have the system operational within a minimal amount of time. If your system is
not already fully integrated with a motherboard, processor, system memory etc.,
please turn to the chapter or section noted in each step for details on installing
specic components.
2-2 Unpacking the System
You should inspect the box the SuperServer 7047R-TXRF server was shipped in and
note if it was damaged in any way. If the server itself shows damage, you should
le a damage claim with the carrier who delivered it.
Decide on a suitable location for setting up and operating the SuperServer 7047R-
TXRF server. It should be situated in a clean, dust-free area that is well ventilated.
Avoid areas where heat, electrical noise and electromagnetic elds are generated.
You will also need it placed near a grounded power outlet.
!
!
Warnings and Precautions!
•Review the electrical and general safety precautions in Chapter 4.
• Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
•Allow the power supply units and Serial ATA drives to cool before touching
them.
•To maintain proper cooling, always keep all chassis panels closed when not
being serviced.
- SUPER 1
- About This Manual 3
- Manual Organization 3
- Table of Contents 6
- Chapter 3 System Interface 7
- Chapter 4 System Safety 7
- Chapter 1 9
- Introduction 9
- 1-2 Serverboard Features 10
- 1-3 Server Chassis Features 11
- DMI: LANE 12
- Reversal 12
- 1-4 Contacting Supermicro 13
- Chapter 2 15
- System Setup 15
- 2-3 Preparing for Setup 16
- Warnings and Precautions! 16
- •Allow the hot plug SMicro12 17
- Reliable Ground 18
- Chassis Cover 19
- Chassis Feet 19
- Chassis Cover Lock 19
- Chassis Handle 20
- Inner Rails 20
- Slide into the Inner Rail 21
- Secure to the 21
- Rear of the Rack 21
- Attach to Middle Rail 21
- Installing the Chassis Cover 23
- Chassis Foot 24
- Receptacle 24
- Chassis Screw 24
- Chapter 3 25
- System Interface 25
- 3-2 Control Panel Buttons 26
- 3-3 Control Panel LEDs 26
- Overheat/Fan Fail 27
- Power Fail 27
- 3-4 Drive Carrier LEDs 28
- Chapter 4 29
- System Safety 29
- 4-3 ESD Precautions 31
- 4-4 Operating Precautions 32
- Chapter 5 33
- Advanced Serverboard Setup 33
- •Control Panel cable (JF1) 34
- 5-3 I/O Ports 35
- OPEN 1st 36
- WARNING! 36
- 5-6 Installing Memory 40
- UDIMM Memory Support 42
- RDIMM Memory Support 42
- LRDIMM Memory Support 42
- 5-6 Adding PCI Add-On Cards 43
- 5-7 Serverboard Details 44
- 5-8 Connector Denitions 46
- USB 4, 5, 6,8 48
- Pin # Denition 48
- USB 7, 9 48
- Pin # Denition 48
- VGA Enable/Disable Jumper 53
- Settings 53
- Jumper Setting Denition 53
- Pins 1-2 Enabled 53
- Pins 2-3 Disabled 53
- 5-10 Onboard Indicators 55
- 5-11 SATA Ports 56
- 5-12 Installing Software 57
- Supero Doctor III 58
- Chapter 6 61
- Advanced Chassis Setup 61
- 6-1 Static-Sensitive Devices 62
- 6-2 Control Panel 62
- 6-3 System Cooling 63
- Rear Fan Release 64
- Mid Fan 64
- Release Tab 64
- 6-4 Power Supply 65
- Power Supply Connections 66
- Tower or Rack Conguration 67
- Rotating the Storage Module 68
- Removing a Drive Carrier 70
- Hard Drive 71
- Hard Drive Tray 71
- Adding Peripheral Drives 72
- Drive Tray Handle 73
- Release Button 73
- Drive Tray 74
- SAS/SATA 74
- Chapter 7 75
- 7-2 Main Setup 76
- Boot Features 78
- •Type of CPU 79
- •CPU Signature 79
- •Microcode Patch 79
- Chipset Conguration 84
- North Bridge 84
- Integrated IO Conguration 84
- QPI Conguration 85
- DIMM Conguration 86
- DIMM Information 86
- South Bridge Conguration 88
- SATA Conguration 89
- PCIe/PCI/PnP Conguration 90
- Super IO Conguration 92
- Serial Port 1 Conguration 92
- Serial Port 2 Conguration 92
- Console Redirection Settings 93
- Console Redirection Settings 95
- ACPI Settings 96
- TPM Enable Status 97
- NIC Conguration 98
- •Factory MAC Address 99
- •Alternate MAC Address 99
- 7-5 IPMI 101
- BMC Network Conguration 102
- 7-6 Boot 103
- 7-7 Security 104
- 7-8 Save & Exit 105
- Appendix A 107
- BIOS Error Beep Codes 107
- Appendix B 109
- System Specications 109
Související produkty a manuály pro Barebone serveru Supermicro SuperServer 7047R-TXRF
Barebone serveru Supermicro 188411 Uživatelský manuál
(122 stránky)
(122 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce