Supermicro SBA-7222G-T2 Uživatelský manuál

SBA-7222G-T2Blade ModuleUser’s ManualRevison 1.0a

SBI-7226T-T2 Blade Module User’s ManualxNotes

xiList of TablesTable 1-1. SBA-7222G-T2 Blade Specification Features...1-2Table 3-1. Populating Memory Slots per Node f

SBI-7226T-T2 Blade Module User’s ManualxiiNotes

1-1Chapter 1Introduction1-1 OverviewThe SBA-7222G-T2 blade module is a compact self-contained server that connects into a pre-cabled enclosure that pr

SBA-7222G-T2 Blade Module User’s Manual1-21-3 Blade Module FeaturesTable 1-1 lists the main features of the SBA-7222G-T2 blade module. See the proceed

1-3Chapter 1: IntroductionDetails on installation of memory modules into the SBA-7222G-T2 blade module are found in Chapter 3: "Setup and Install

SBA-7222G-T2 Blade Module User’s Manual1-4Figure 1-1. Full Rack of Blade Enclosures and Blade Servers

1-5Chapter 1: Introduction1-4 Contacting SupermicroHeadquartersAddress: Super Micro Computer, Inc.980 Rock Ave.San Jose, CA 95131 U.S.A.Tel: +1 (408)

SBA-7222G-T2 Blade Module User’s Manual1-6Notes

2-1Chapter 2System Safety2-1 Electrical Safety PrecautionsBasic electrical safety precautions should be followed to protect yourself from harm and the

SBA-7222G-T2 Blade Module User’s ManualiiThe information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor

SBA-7222G-T2 Blade Module User’s Manual2-2only. The new fuse must be the same or equivalent as the one replaced. Contact technical support for details

2-3Chapter 2: System Safety2-4 Operating PrecautionsCare must be taken to assure that the cover of the blade unit is in place when the blade is operat

SBA-7222G-T2 Blade Module User’s Manual2-4Notes

3-1Chapter 3Setup and Installation3-1 OverviewThis chapter covers the setup and installation of the blade module and its components.3-2 Installing Bla

SBA-7222G-T2 Blade Module User’s Manual3-2Removing/Replacing the Blade CoverThe blade cover must be removed to access the mainboard when you need to i

3-3Chapter 3: Setup and InstallationFigure 3-1. Inserting a Blade into the EnclosureFigure 3-2. Locking the Blade into Position

SBA-7222G-T2 Blade Module User’s Manual3-43-3 Processor InstallationOne or two 1944-pin G34 socket AMD Opteron 6100 series processors may be installed

3-5Chapter 3: Setup and Installation7. To install the heatsink, apply thermal grease to the top of the processor. (If reinstalling a heatsink, first c

SBA-7222G-T2 Blade Module User’s Manual3-6Figure 3-4. Installing the Onboard Battery3-5 Memory InstallationThe mainboard of each blade unit must be po

3-7Chapter 3: Setup and InstallationFigure 3-5. 8-Slot DIMM Numbering for Two Node Blade ModulesEdge of BoardToward CPUToward CPUEdge of BoardToward C

iiiPrefaceAbout this ManualThis manual is written for professional system integrators, Information Technology professionals, service personnel and tec

SBA-7222G-T2 Blade Module User’s Manual3-8DIMM InstallationInstalling DIMM Memory Modules1. Power down the blade module (see "Powering Down a Bla

3-9Chapter 3: Setup and Installation3-6 Hard Disk Drive InstallationHard disk drives are installed in “carriers” which are hot-swappable and can be re

SBA-7222G-T2 Blade Module User’s Manual3-10Figure 3-7. Installing a Hard Drive in a Carrier

3-11Chapter 3: Setup and Installation3-7 Installing the Operating SystemAn operating system (OS) must be installed on each blade module. Blades with M

SBA-7222G-T2 Blade Module User’s Manual3-12Installing via Virtual Media (Drive Redirection)You can install the OS via Virtual Media through either the

4-1Chapter 4Blade Module FeaturesFigure 4-1. SBA-7222G-T2 Blade Unit Front ViewThis chapter describes the SBA-7222G-T2 blade unit. Installation and ma

SBA-7222G-T2 Blade Module User’s Manual4-24-1 Control PanelEach blade has a similar control panel (Figure 4-2) with power on/off button, a KVM connect

4-3Chapter 4: Blade Module FeaturesPower ButtonEach blade has its own power button so that individual blade units within the enclosure may be turned o

SBA-7222G-T2 Blade Module User’s Manual4-44-2 MainboardThe mainboard of the SBA-7222G-T2 blade unit is a proprietary design, which is based on the AMD

4-5Chapter 4: Blade Module FeaturesTable 4-4. BHDGT Mainboard Layout Item Description1 CPU1 Socket2 CPU2 Socket3 CPU3 Socket4 CPU4 Socket5DIMM Slots (

SBA-7222G-T2 Blade Module User’s ManualivNotes

SBA-7222G-T2 Blade Module User’s Manual4-6Figure 4-4. BHDGT Block DiagramJumpersThe jumpers present on the mainboard are used by the manufacturer only

4-7Chapter 4: Blade Module Features4-3 Blade Unit ComponentsFigure 4-5. Exploded View of SBA-7222G-T2 Blade Module12234354322

SBA-7222G-T2 Blade Module User’s Manual4-8Memory SupportEach node of the SBA-7222G-T2 blade module each supports up to 128 GB of ECC Registered DDR3-1

5-1Chapter 5RAID Setup ProcedureEach SBA-7222G-T2 blade module supports four hard drives, two per node, which may be used to create a RAID array. Impo

SBA-7222G-T2 Blade Module User’s Manual5-2See Chapter 6 for information on using your system’s BIOS setup.Setting up the BIOS for RAID1. In the ADVANC

5-3Chapter 5: RAID Setup Procedure3. Press the Esc key once to exit the IDE CONFIGURATION screen and go to the EXIT menu in the BIOS setup. From the E

SBA-7222G-T2 Blade Module User’s Manual5-44. Your system will reboot. When the reboot displays the screen message in Figure 5-3 press CTRL-A to bring

6-1Chapter 6BIOS6-1 IntroductionThis document describes the AMI® BIOS Setup utility for the SBA-7222G-T2 Blade Module. The AMI ROM BIOS is stored in a

SBA-7222G-T2 Blade Module User’s Manual6-2Items that use sub-menus are indicated with the  icon. With the item highlighted, press the <ENTER> k

6-3Chapter 6: BIOSBoot FeatureThe menu options in the BOOT FEATURE submenu and their descriptions are shown in Table 6-1.Table 6-1. Boot Feature Subme

vTable of ContentsChapter 1 Introduction...1-11-1 Overview...

SBA-7222G-T2 Blade Module User’s Manual6-4Processor & Clock OptionsThe menu options in the PROCESSOR & CLOCK OPTIONS submenu and their descrip

6-5Chapter 6: BIOSCS Sparing EnableThis option reserves a spare memory rank in each node. Options include Enabled and Disabled.Bank Swizzle ModeThis o

SBA-7222G-T2 Blade Module User’s Manual6-6IDE ConfigurationThe menu options in the IDE ConfiguraTION submenu and their descriptions are shown in Table

6-7Chapter 6: BIOSPCI/PnP ConfigurationThe menu options in the PCI/PNP CONFIGURATION submenu and their descriptions are shown in Table 6-5.DMA ModeSel

SBA-7222G-T2 Blade Module User’s Manual6-8Super IO Device ConfigurationThe menu options in the SUPER IO CONFIGURATION submenu and their descriptions a

6-9Chapter 6: BIOSHardware Health ConfigurationThe menu options in the HARDWARE HEALTH CONFIGURATION submenu and their descriptions are shown in Table

SBA-7222G-T2 Blade Module User’s Manual6-10IPMI ConfigurationThe menu options in the IPMI CONFIGURATION submenu and their descriptions are shown in Ta

6-11Chapter 6: BIOSEvent Log ConfigurationThe menu options in the EVENT LOG CONFIGURATION submenu and their descriptions are shown in Table 6-11.6-4 S

SBA-7222G-T2 Blade Module User’s Manual6-126-5 Boot MenuThe menu options for the BOOT menu are shown in Table 6-13.Table 6-13. Boot MenuMenu Option De

6-13Chapter 6: BIOS6-6 Exit MenuSelect the EXIT tab from AMI BIOS SETUP UTILITY screen to enter the EXIT BIOS SETUP screen. The options for the EXIT m

SBI-7226T-T2 Blade Module User’s ManualviInstalling via Virtual Media (Drive Redirection) ...3-12Linux Installation

SBA-7222G-T2 Blade Module User’s Manual6-14Notes

A-1Appendix ABIOS POST CodesA-1 BIOS POST MessagesDuring the Power-On Self-Test (POST), the BIOS will check for problems. If a problem is found, the B

SBA-7222G-T2 Blade Module User’s ManualA-2Previous boot incomplete - Default configuration usedPrevious POST did not complete successfully. POST loads

A-3:nnnn kB Extended RAM PassedWhere nnnn is the amount of RAM in kilobytes successfully tested.nnnn Cache SRAM PassedWhere nnnn is the amount of syst

SBA-7222G-T2 Blade Module User’s ManualA-4A-2 BIOS POST CodesThis section lists the POST (Power-On Self-Test) codes for the AMI BIOS. POST codes are d

A-5:Bootblock Recovery CodesThe bootblock recovery checkpoint codes are listed in order of execution in Table A-3.Table A-3. Bootblock Recovery Error

SBA-7222G-T2 Blade Module User’s ManualA-6Uncompressed Initialization CodesThe following runtime checkpoint codes are listed in order of execution in

A-7:1AhThe memory refresh line is toggling. Checking the 15 second on/off time next.2BhPassing control to the video ROM to perform any required config

SBA-7222G-T2 Blade Module User’s ManualA-840hPreparing the descriptor tables next.42hThe descriptor tables are prepared. Entering protected mode for t

A-9:59hThe Hit <DEL> message is cleared. The <WAIT...> message is displayed. Starting the DMA and interrupt controller test next.60hThe DM

vii6-5 Boot Menu ...6-126-6 Exit Menu...

SBA-7222G-T2 Blade Module User’s ManualA-10Notes95hInitializing the bus option ROMs from C800 next. See the last page of this chapter for additional i

A-11:B1hCopying any code to specific areas.00hCode copying to specific areas is done. Passing control to INT 19h boot loader next.Table A-4. Uncompres

SBA-7222G-T2 Blade Module User’s ManualA-12Notes

DisclaimerThe products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or

SBA-7222G-T2 Blade Module User’s Manual

SBI-7226T-T2 Blade Module User’s ManualviiiNotes

ixList of FiguresFigure 1-1. Full Rack of Blade Enclosures and Blade Servers .......1-4Figure 3-1. Inserting a Blade into the Enclos