Supermicro SYS-7047R-3RF4+ Datový list Strana 41
- Strana / 108
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 5: Advanced Serverboard Setup
5-11
DIMM Module Population Table
Follow the table below when installing memory.
Processors and their Corresponding Memory Slots
CPU# Corresponding Memory Slot
CPU 1 (P1-) A1 B1 C1 D1 A2 B2 C2 D2 A3 B3 C3 D3
CPU2 (P2-) E1 F1 G1 H1 E2 F2 G2 H2 E3 F3 G3 H3
Processor and Memory Module Population
Number of
CPUs+DIMMs
CPU and Memory Population Confi guration Table
(For memory to work properly, please install DIMMs according to this table)
1 CPU &
3 DIMMs
CPU1
P1-A1/P1-B1/P1-C1
1 CPU &
6 DIMMs
CPU1
P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2
1 CPU &
9 DIMMs
CPU1
P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2/P1-C2/P1-D2/P1-A3
1 CPU &
12 DIMMs
CPU1
P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2/P1-C2/P1-D2/P1-A3/P1-B3/P1-C3/P1-D3
2 CPUs &
6 DIMMs
CPU1 + CPU2
P1-A1/P1-B1/P1-C1
P2-E1/P2-F1/P2-G1
2 CPUs &
12 DIMMs
CPU1 + CPU2
P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2
P2-E1/P2-F1/P2-G1/P2-H1/P2-E2/P2-F2
2 CPUs &
16 DIMMs
CPU1 + CPU2
P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2/P1-C2/P1-D2
P2-E1/P2-F1/P2-G1/P2-H1/P2-E2/P2-F2/P2-G2/P2-H2
2 CPUs &
18 DIMMs
CPU1 + CPU2
P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2/P1-C2/P1-D2/P1-A3
P2-E1/P2-F1/P2-G1/P2-H1/P2-E2/P2-F2/P2-G2/P2-H2/P2-E3
2 CPUs &
24 DIMMs
CPU1/CPU2
P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2/P1-C2/P1-D2/P1-A3/P1-B3/P1-C3/P1-D3
P2-E1/P2-F1/P2-G1/P2-H1/P2-E2/P2-F2/P2-G2/P2-H2/P2-E3/P2-F3/P2-G3/P2-H3
RDIMM Support POR on the Sandy Bridge-EP Series Processor Platform
(To Be Updated)
DIMM Slots
per DDR
Channel
DIMMs
Populated
per DDR
Channel
RDIMM Type
(RDIMM: Reg.=
Registered)
POR Speeds (in MHz) Ranks per DIMM
(Any Combination)
1 1 Reg. ECC DDR3 800, 1066, 1333, 1600 SR, DR, or QR
2 1 Reg. ECC DDR3 800, 1066, 1333, 1600 SR, DR, or QR
2 2 Reg. ECC DDR3 800, 1066, 1333, 1600 Mixing SR, DR, QR
Population Rules:
1. Any combination of x4 and x8 RDIMMs with 1 Gb or 2 Gb DRAM density are supported.
2. Populate DIMMs starting with DIMM1A.
3. When mixing QR with SR or DR on the same DDR channel, put the QR in DIMM1A fi rst.
- SUPER 1
- Manual Revision 1.0 2
- About This Manual 3
- Manual Organization 3
- Table of Contents 6
- Chapter 4 System Safety 7
- Chapter 1 9
- Introduction 9
- 1-2 Serverboard Features 10
- 1-3 Server Chassis Features 11
- System Block Diagram 12
- 1-4 Contacting Supermicro 13
- Chapter 2 15
- Server Installation 15
- Warnings and Precautions! 16
- Rack Mounting Considerations 17
- Inner rail 18
- Outer rail 18
- Rail brackets 18
- Installing the Chassis Rails 19
- Installing the Rack Rails 20
- Chapter 3 23
- System Interface 23
- 3-3 Control Panel LEDs 24
- 3-4 Drive Carrier LEDs 25
- Chapter 4 27
- System Safety 27
- 4-3 ESD Precautions 29
- 4-4 Operating Precautions 30
- Chapter 5 31
- Advanced Serverboard Setup 31
- 5-2 Serverboard Installation 32
- • Control Panel cable (JF1) 33
- 2 1 34
- 20 19 34
- Press down on 35
- 'Close 1st' 35
- Pull lever away 35
- WARNING! 36
- OPEN 1st 37
- Removing the Heatsink 39
- 5-6 Installing Memory 40
- 5-7 Adding PCI Add-On Cards 42
- 5-8 Serverboard Details 43
- X9DR3-LN4F+ Quick Reference 44
- 5-9 Connector Defi nitions 46
- VGA Enable/Disable 53
- Jumper Settings 53
- Pins 1-2 Enabled 53
- Pins 2-3 Disabled 53
- 5-11 Onboard Indicators 57
- 5-12 SATA and SAS Ports 58
- 5-13 Installing Software 59
- SuperDoctor III 60
- Chapter 6 63
- Advanced Chassis Setup 63
- System ResetMain Power 64
- 5.25" Drive Bays (2) 64
- USB Ports 64
- 8 Hard Drive Bays 64
- (behind locking bezel) 64
- 6-2 Front Control Panel 65
- 6-3 System Fans 66
- 6-4 Drive Bay Installation 68
- SAS/SATA Backplane 69
- Storage Module 70
- Release Lever 71
- 6-5 Power Supply 72
- Chapter 7 73
- 7-2 Main Setup 74
- Boot Features 75
- Power Confi guration 76
- CPU Confi guration 77
- Chipset Confi guration 81
- North Bridge 81
- Integrated IO Confi guration 81
- QPI Confi guration 82
- DIMM Confi guration 83
- DIMM Information 83
- South Bridge Confi guration 85
- SATA Confi guration 85
- PCIe/PCI/PnP Confi guration 87
- Super IO Confi guration 89
- Serial Port 1 Confi guration 89
- Serial Port 2 Confi guration 89
- • COM 1/COM 2 90
- ACPI Setting 92
- TPM Enable Status 93
- NIC Confi guration 94
- 7-3 Event Logs 95
- 7-4 IPMI 97
- BMC Network Confi guration 98
- 7-5 Boot 99
- 7-6 Security 100
- 7-7 Save & Exit 101
- • LAN Device 102
- • UEFI: Built-in EFI Shell 102
- Appendix A 103
- BIOS Error Beep Codes 103
- System Specifi cations 105
- Appendix B 105
Související produkty a manuály pro Barebone serveru Supermicro SYS-7047R-3RF4+
Barebone serveru Supermicro SYS-7037A-I Datový list
(102 stránky)
(102 stránky)
Barebone serveru Supermicro SYS-6015TW-TB Datový list
(132 stránky)
(132 stránky)
Barebone serveru Supermicro SYS-8015C-TB Datový list
(118 stránky)
(118 stránky)
Barebone serveru Supermicro SYS-6015P-TRB Datový list
(120 stránky)
(120 stránky)
Barebone serveru Supermicro SYS-5013C-MT Datový list
(112 stránky)
(112 stránky)
Barebone serveru Supermicro SYS-6014H-32B Datový list
(126 stránky)
(126 stránky)
Barebone serveru Supermicro SYS-5013C-T Datový list
(118 stránky)
(118 stránky)
Barebone serveru Supermicro SYS-6015C-MTB Datový list
(118 stránky)
(118 stránky)
Barebone serveru Supermicro SYS-1025W-URB Datový list
(112 stránky)
(112 stránky)
Barebone serveru Supermicro SYS-6015C-URV Datový list
(110 stránky)
(110 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce