Supermicro SYS-6015T-TB Uživatelský manuál

SUPERSUPERSERVER 6015T-TSUPERSERVER 6015T-INF USER’S MANUAL Revision 1.0b®

xNotesSUPERSERVER 6015T-T/6015T-INF User's Manual

B-6SUPERSERVER 6015T-T/6015T-INF User's ManualNotes

Appendix C: Intel HostRAID Setup GuidelinesC-1 Appendix C Intel HostRAID Setup Guidelines After all the hardw

C-2SUPERSERVER 6015T-T/6015T-INF User's ManualThe Intel HostRAID Confi gurationsThe following RAID levels are supported:RAID 0 (Data Striping): th

Appendix C: Intel HostRAID Setup GuidelinesC-3Using the Intel ESB2 SATA RAID Utility Program1. Creating, Deleting and Resetting RAID Volumes: a. After

C-4SUPERSERVER 6015T-T/6015T-INF User's Manualb. Specify a name for the RAID 0 set and press the <Tab> key or the <Enter> key to go t

Appendix C: Intel HostRAID Setup GuidelinesC-5Creating a RAID 1 Volumea. Select "Create RAID Volume" from the main menu and press the <En

C-6SUPERSERVER 6015T-T/6015T-INF User's ManualCreating a RAID 10 (RAID 1+ RAID 0)a. Select "Create RAID Volume" from the main menu and

Appendix C: Intel HostRAID Setup GuidelinesC-7Creating a RAID 5 Set (Parity)a. Select "Create RAID Volume" from the main menu and press the

C-8SUPERSERVER 6015T-T/6015T-INF User's ManualDeleting a RAID Volume Warning: Make sure you back up your data before deleting a RAID set.

Appendix C: Intel HostRAID Setup GuidelinesC-9Resetting to Non-RAID and Resetting a RAID HDDWarning: Be cautious when you reset a RAID volume HDD to n

Chapter 1 Introduction1-1 OverviewThe SuperServer 6015T-T/6015T-INF is a "1U Twin" server comprised of the SC808T-980 1U c

C-10SUPERSERVER 6015T-T/6015T-INF User's ManualC-2 Installing Windows XP/2000/2003 for RAID SystemsNote: If you wish to have SATA RAID functions

D-1Appendix D: System Specifi cations Appendix D System Specifi cationsN

D-2SUPERSERVER 6015T-T/6015T-INF User's ManualChassis SC808T-980 (1U Rackmount) Dimensions: (WxHxD) 17.2 x 1.7 x 27.75 in. (437 x 4

D-3Appendix D: System Specifi cationsRegulatory Compliance Electromagnetic Emissions: FCC Class A, EN 55022 Class A, EN 61000-3-2/-3-3, CISPR

D-4SUPERSERVER 6015T-T/6015T-INF User's ManualNotes

1-2SUPERSERVER 6015T-T/6015T-INF User's Manual1-2 Serverboard FeaturesAt the heart of the SuperServer 6015T-T/6015T-INF lies two X7DBT-T/X7DBT-IN

Chapter 1: Introduction1-3Onboard Controllers/PortsAn onboard IDE controller supports Ultra ATA 100 hard drives or ATAPI devices. Onboard I/O backpan

1-4SUPERSERVER 6015T-T/6015T-INF User's ManualFigure 1-1 . Intel 5000P Chipset: System Block Diagram Note: This is a general block diagram. Ple

Chapter 1: Introduction1-51-3 Server Chassis FeaturesThe following is a general outline of the main features of the SC808T-980 1U chas-sis. Details o

1-6SUPERSERVER 6015T-T/6015T-INF User's Manual1-4 1U Twin: System NotesAs a 1U Twin confi guration, the 6015T-T/6015T-INF is a unique server syste

Chapter 1: Introduction1-71-5 Contacting SupermicroHeadquartersAddress: Super Micro Computer, Inc.980 Rock Ave.San Jose, CA 95131 U.S.A.Tel: +1 (40

1-8SUPERSERVER 6015T-T/6015T-INF User's ManualNotes

Chapter 2: Server Installation2-1 Chapter 2 Server Installation 2-1 OverviewThis chapter provides a quick setup

Manual Revision 1.0b Release Date: April 7, 2008The information in this User’s Manual has been carefully reviewed and is believed to be accurate

2-2SUPERSERVER 6015T-T/6015T-INF User's ManualChoosing a Setup Location - Leave enough clearance in front of the rack to enable you to open

Chapter 2: Server Installation2-3Rack Mounting ConsiderationsAmbient Operating TemperatureIf installed in a closed or multi-unit rack assembly, the am

2-4SUPERSERVER 6015T-T/6015T-INF User's Manual2-4 Installing the System into a RackThis section provides information on installing the 6015T-T/6

Chapter 2: Server Installation2-5Installing the Outer RailsBegin by measuring the distance from the front rail to the rear rail of the rack. Attach a

2-6SUPERSERVER 6015T-T/6015T-INF User's ManualInstalling the Server into the RackYou should now have rails attached to both the chassis and the r

Chapter 2: Server Installation2-7Figure 2-3. Installing the Server into a Rack

2-8SUPERSERVER 6015T-T/6015T-INF User's Manual2-5 Checking the Serverboard SetupAfter you install the 6015T-T/6015T-INF in the rack, you will ne

Chapter 2: Server Installation2-9Figure 2-4. Accessing the Inside of the System

2-10SUPERSERVER 6015T-T/6015T-INF User's Manual2-6 Checking the Drive Bay SetupNext, you should check to make sure the peripheral drives and the

Chapter 3: System Interface3-1Chapter 3 System Interface3-1 OverviewThere are several LEDs on the two control panels as well as others on the S

PrefaceAbout This ManualThis manual is written for professional system integrators and PC technicians. It provides information for the installation a

3-2SUPERSERVER 6015T-T/6015T-INF User's Manual3-3 Control Panel LEDsEach of the two control panels located on the front of the SC808T-980 chassis

Chapter 3: System Interface3-3 Power: Indicates power is being supplied to the system's power supply unit. This LED should normally be illumi

3-4SUPERSERVER 6015T-T/6015T-INF User's ManualNotes

Chapter 4: System Safety4-1 Chapter 4 System Safety4-1 Electrical Safety Precautions!Basic electrical safety precautions should be f

SUPERSERVER 6015T-T/6015T-INF User's Manual4-24-2 General Safety PrecautionsFollow these rules to ensure general safety:  Keep the area around

Chapter 4: System Safety4-34-3 ESD PrecautionsElectrostatic discharge (ESD) is generated by two objects with different electrical charges coming into

SUPERSERVER 6015T-T/6015T-INF User's Manual4-44-4 Operating PrecautionsCare must be taken to assure that the chassis cover is in place when the 6

Chapter 5: Advanced Serverboard Setup5-1 Chapter 5 Advanced Serverboard SetupThis chapter covers the steps required to install the X7

5-2SUPERSERVER 6015T-T/6015T-INF User's Manual5-2 Serverboard InstallationThis section explains the fi rst step of physically mounting the X7DBT-T

Chapter 5: Advanced Serverboard Setup5-35-3 Connecting CablesNow that the serverboards are installed, the next step is to connect the cables to the bo

SUPERSERVER 6015T-T/6015T-INF User's ManualivChapter 4: System SafetyYou should thoroughly familiarize yourself with this chapter for a general

5-4SUPERSERVER 6015T-T/6015T-INF User's Manual5-4 I/O PortsThe I/O ports are color coded in conformance with the PC 99 specifi cation. See Figure

Chapter 5: Advanced Serverboard Setup5-55-5 Processor and Heatsink InstallationIMPORTANT! Always connect the power cord last and remove it fi rst befo

5-6SUPERSERVER 6015T-T/6015T-INF User's ManualSocket keyCPU installed in socketPnP cap released from load plate3. Use your thumb and your index fi

Chapter 5: Advanced Serverboard Setup5-7Warning! We do not recommend that the CPU or the heatsink be removed. However, if you do need to uninstall t

5-8SUPERSERVER 6015T-T/6015T-INF User's Manual5-6 Installing Memory 1. Memory support The X7DBT-T/X7DBT-INF has eight 240-pin DIMM

Chapter 5: Advanced Serverboard Setup5-95-7 Adding PCI Cards1. 64-bit PCI-X slotThe 6015T-T/6015T-INF includes two preinstalled riser cards designed s

5-10SUPERSERVER 6015T-T/6015T-INF User's Manual Figure 5-4. X7DBT-T/X7DBT-INF Layout (not drawn to scale)Jumpers not indicated are for test pu

Chapter 5: Advanced Serverboard Setup5-11X7DBT-T/X7DBT-INF Quick ReferenceJumper Description Default Setting JBT1 CMOS Clear See Section

5-12SUPERSERVER 6015T-T/6015T-INF User's ManualReset ConnectorThe reset connector is located on pins 3 and 4 of JF1 and attaches to the reset swi

Chapter 5: Advanced Serverboard Setup5-13Overheat LED (OH)Connect an LED to the OH connection on pins 7 and 8 of JF1 to provide ad-vanced warning of c

vPrefaceNotes

5-14SUPERSERVER 6015T-T/6015T-INF User's ManualChassis IntrusionThe Chassis Intrusion header is des-ignated JL1. See the board layout for the lo

Chapter 5: Advanced Serverboard Setup5-15Wake-On-LANThe Wake-On-LAN header is des-ignated JWOL on the serverboard. See the table on the right for pin

5-16SUPERSERVER 6015T-T/6015T-INF User's ManualWake-On-RingThe Wake-On-Ring header is designated JWOR. This function allows your computer to rec

Chapter 5: Advanced Serverboard Setup5-17SMB Power (I2C)The header at JI2C is for I2C, which may be used to monitor the status of the power supply, fa

5-18SUPERSERVER 6015T-T/6015T-INF User's Manual5-10 Jumper SettingsExplanation of JumpersTo modify the operation of the serverboard, jumpers

Chapter 5: Advanced Serverboard Setup5-19Watch Dog Enable/Disable JWD enables the Watch Dog function, a system monitor that takes action when a softwa

5-20SUPERSERVER 6015T-T/6015T-INF User's Manual5-11 Onboard IndicatorsLAN1/LAN2 LEDsThe Ethernet ports (located beside the VGA port) have two LED

Chapter 6: Advanced Chassis Setup6-1Chapter 6 Advanced Chassis SetupThis chapter covers the steps required to install components and perform ma

6-2SUPERSERVER 6015T-T/6015T-INF User's ManualFigure 6-2. Chassis Rear View6-2 Control PanelEach control panel on the front of the chassis must

Chapter 6: Advanced Chassis Setup6-36-3 System FansEach serverboard has its own set of three 4-cm high-performance fans (for a total of six in the cha

viTable of ContentsPrefaceAbout This Manual ... ii

6-4SUPERSERVER 6015T-T/6015T-INF User's ManualFigure 6-3. Mounting a Drive in a Carrier2. Installing/removing hot-swap SATA drives The drive

Chapter 6: Advanced Chassis Setup6-56-5 Power SupplyThe SuperServer 6015T-T/6015T-INF has a single 980 watt power supply. This power supply has the c

6-6SUPERSERVER 6015T-T/6015T-INF User's ManualFigure 6-4. Removing the Power Supply

Chapter 7: BIOS7-1 Chapter 7 BIOS 7-1 IntroductionThis chapter describes the Phoenix BIOS™ Setup utility for the X7DBT/X7DBT

7-2SUPERSERVER 6015T-T/6015T-INF User's Manual7-2 Running SetupDefault settings are in bold text unless otherwise noted.The BIOS setup options de

Chapter 7: BIOS7-3Main BIOS Setup MenuMain Setup FeaturesSystem TimeTo set the system date and time, key in the correct information in the appropriate

7-4SUPERSERVER 6015T-T/6015T-INF User's ManualIDE Channel 0 Master/Slave, IDE Channel 1 Master/Slave, SATA Port2 and SATA Port3These settings al

Chapter 7: BIOS7-532 Bit I/OThis option allows the user to enable or disable the function of 32-bit data transfer. The options are Enabled and Disabl

7-6SUPERSERVER 6015T-T/6015T-INF User's ManualSATA AHCI (Available when SATA RAID is Disabled)Select Enable to enable the function of Serial ATA

Chapter 7: BIOS7-77-4 Advanced Setup Choose Advanced from the Phoenix BIOS Setup Utility main menu with the arrow keys. You should see the followin

HDD ... 3-2Power ...

7-8SUPERSERVER 6015T-T/6015T-INF User's ManualACPI ModeUse this setting to determine if you want to employ ACPI (Advanced Confi guration and Power

Chapter 7: BIOS7-9Cache Base 0-512KIf enabled, this feature will allow the data stored in the base memory area: block 0-512K to be cached (written) i

7-10SUPERSERVER 6015T-T/6015T-INF User's ManualPCI Confi gurationAccess the submenu to make changes to the following settings for PCI devices.Onb

Chapter 7: BIOS7-11Slot1 PCI-Exp x8Access the submenu for each of the settings above to make changes to the following:Option ROM ScanWhen enabled, th

7-12SUPERSERVER 6015T-T/6015T-INF User's ManualMemory Branch ModeThis option determines how the two memory branches operate. System address space

Chapter 7: BIOS7-13Snoop FilterSelect Enabled to eliminate snoop traffi c to the graphics port to improve system performance when running graphics inte

7-14SUPERSERVER 6015T-T/6015T-INF User's ManualAdvanced Processor OptionsAccess the submenu to make changes to the following settings. CPU Speed

Chapter 7: BIOS7-15Adjacent Cache Line Prefetch (Available when supported by the CPU.)The CPU fetches the cache line for 64 bytes if this option is se

7-16SUPERSERVER 6015T-T/6015T-INF User's ManualI/O Device Confi gurationAccess the submenu to make changes to the following settings. Serial Port

Chapter 7: BIOS7-17Console Redirection Access the submenu to make changes to the following settings. COM Port AddressThis item allows you to specify

viiiWake-On-Ring ... 5-16Serial Ports ...

7-18SUPERSERVER 6015T-T/6015T-INF User's ManualHardware Monitor LogicNote: Phoenix BIOS will automatically detect the type of CPU(s) and hardwar

Chapter 7: BIOS7-19Hardware Monitor LogicCPU Temperature Threshold (See note on page 7-18)This option allows the user to set a CPU temperature thres

7-20SUPERSERVER 6015T-T/6015T-INF User's ManualHardware Monitor Logic (See note on page 7-18.)CPU Temperature ThresholdThis option allows the u

Chapter 7: BIOS7-21IPMI (Available only when an IPMI card is installed)IPMI Specifi cation Version: This item displays the current IPMI Version.Firmwa

7-22SUPERSERVER 6015T-T/6015T-INF User's ManualOS Boot Watch DogSet to Enabled to enable OS Boot Watch Dog. The options are Enabled and Disabled.

Chapter 7: BIOS7-23Realtime Sensor DataThis feature display information from motherboard sensors, such as temperatures, fan speeds and voltages of va

7-24SUPERSERVER 6015T-T/6015T-INF User's Manual7-5 SecurityChoose Security from the Phoenix BIOS Setup Utility main menu with the arrow keys. Yo

Chapter 7: BIOS7-25Password on BootThis setting allows you to require a password to be entered when the system boots up. The options are Enabled (pas

7-26SUPERSERVER 6015T-T/6015T-INF User's Manual7-7 ExitChoose Exit from the Phoenix BIOS Setup Utility main menu with the arrow keys. You should

A-1Appendix A: BIOS POST Messages Appendix A BIOS POST MessagesDuring the Power-On Self-Test (POST), the BIOS will check for problems.

Table of ContentsixAppendices:Appendix A: BIOS POST Messages Appendix B: BIOS POST Codes Appendix C: Intel HostRAID Setup Guidelines Appendix D: Syste

A-2SUPERSERVER 6015T-T/6015T-INF User's ManualSystem CMOS checksum bad - Default confi guration usedSystem CMOS has been corrupted or modifi ed inc

A-3Appendix A: BIOS POST MessagesSystem cache error - Cache disabledRAM cache failed and BIOS disabled the cache. On older boards, check the cache jum

A-4SUPERSERVER 6015T-T/6015T-INF User's ManualInvalid System Confi guration DataProblem with NVRAM (CMOS) data.I/O device IRQ confl ictI/O device I

A-5Appendix A: BIOS POST MessagesPress <F1> to resume, <F2> to Setup, <F3> for previous Displayed after any recoverable error messag

A-6SUPERSERVER 6015T-T/6015T-INF User's ManualNotes

Appendix B: BIOS POST CodesB-1This section lists the POST (Power On Self Test) codes for the PhoenixBIOS. POST codes are divided into two categories:

B-2SUPERSERVER 6015T-T/6015T-INF User's ManualPOST Code Description18h 8254 timer initialization1Ah 8237 DMA controller initialization1C

Appendix B: BIOS POST CodesB-3POST Code Description5Ch Test RAM between 512 and 640 kB60h Test extended memory62h Test extended memory ad

B-4SUPERSERVER 6015T-T/6015T-INF User's ManualPOST Code Description99h Check for SMART Drive (optional)9Ch Set up Power Management9Dh

Appendix B: BIOS POST CodesB-5POST Code DescriptionD2h Unknown interruptD4h Check Intel Branding stringD8h Alert Standard Format initializ