Supermicro SYS-7047GR-TPRF Uživatelský manuál stáhnout pdf (Strana 21)

Chapter 2: Workstation Installation

2-7

Figure 2-3. Installing the Inner Rack Rails

Installing the Outer Rails to the Rack

Installing the Outer Rails

1. Attach the rear bracket to the middle bracket.

2. Adjust both the brackets to the proper distance so that the rail ts snugly into

the rack.

3. Secure the rear of the outer rail with two M5 screws and the rear of the rack.

Note: The outer rail is adjustable from approximately 26" to 38.25".

4. Repeat steps 1-3 for the left outer rail.

Figure 2-4. Assembling the Outer Rails

Slide into the Inner Rail

Secure to the

Rear of the Rack

Attach to Middle Rail

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 113 114

SUPER 1
About This Manual 3
Manual Organization 3
Table of Contents 6
Chapter 3 System Interface 7
Chapter 4 System Safety 7
Chapter 1 9
Introduction 9
1-2 Serverboard Features 10
1-3 Chassis Features 11
1-4 GPU Subsystem 12
Chapter 1: Introduction 13
System Block Diagram 13
1-5 Contacting Supermicro 14
Chapter 2 15
Workstation Installation 15
2-3 Preparing for Setup 16
Warnings and Precautions! 16
Rack Mounting Considerations 17
Reliable Ground 18
Chassis Cover 19
Chassis Feet 19
Chassis Cover Lock 19
Chassis Handle 20
Inner Rails 20
Slide into the Inner Rail 21
Secure to the 21
Rear of the Rack 21
Attach to Middle Rail 21
Installing the Chassis Cover 23
Chassis Foot 24
Receptacle 24
Chassis Screw 24
Chapter 3 25
System Interface 25
3-2 Control Panel Buttons 26
3-3 Control Panel LEDs 26
Overheat/Fan Fail 27
Power Fail 27
3-4 Drive Carrier LEDs 28
Chapter 4 29
System Safety 29
4-3 ESD Precautions 31
4-4 Operating Precautions 32
Chapter 5 33
Advanced Serverboard Setup 33
•Control Panel cable (JF1) 34
5-3 I/O Ports 35
OPEN 1st 36
WARNING! 36
5-6 Installing Memory 40
5-6 Adding PCI Add-On Cards 44
5-7 Serverboard Details 45
5-8 Connector Denitions 47
LAN1/2 Enable/Disable 54
Jumper Settings 54
Pins 1-2 Enabled 54
Pins 2-3 Disabled 54
5-10 Onboard Indicators 56
5-11 SATA Ports 57
5-12 Installing Software 58
Supero Doctor III 59
Chapter 6 61
Advanced Chassis Setup 61
6-1 Static-Sensitive Devices 62
6-2 Control Panel 62
6-3 System Cooling 63
FAN-0116L4 65
6-4 Power Supply 66
Power Supply Connections 67
Tower or Rack Conguration 68
Rotating the Storage Module 69
Removing a Drive Carrier 71
Hard Drive 72
Hard Drive Tray 72
Adding Peripheral Drives 73
Drive Tray Handle 74
Release Button 74
Drive Tray 75
SAS/SATA 75
Chapter 7 77
7-2 Main Setup 78
Boot Features 80
•Type of CPU 81
•CPU Signature 81
•Microcode Patch 81
Chipset Conguration 86
North Bridge 86
Integrated IO Conguration 86
QPI Conguration 87
DIMM Conguration 88
DIMM Information 88
South Bridge Conguration 90
SATA Conguration 91
PCIe/PCI/PnP Conguration 92
Super IO Conguration 94
Serial Port 1 Conguration 94
Serial Port 2 Conguration 94
Console Redirection Settings 95
Console Redirection Settings 97
ACPI Settings 97
TPM Enable Status 98
•ME BIOS Interface Version 99
•ME Version 99
NIC Conguration 100
7-4 Event Logs 101
7-5 IPMI 103
BMC Network Conguration 104
7-6 Boot 105
7-7 Security 106
7-8 Save & Exit 107
Appendix A 109
BIOS Error Beep Codes 109
Appendix B 111
System Specications 111

Komentáře k této Příručce

Žádné komentáře

Supermicro SYS-7047GR-TPRF Uživatelský manuál Strana 21

Komentáře k této Příručce

Související produkty a manuály pro Barebone serveru Supermicro SYS-7047GR-TPRF