Supermicro AOC-USASLP-L8I Uživatelský manuál Strana 24
- Strana / 104
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
AOC-USASLP-L8i Add-on Card User’s Manual
4-6
8. Highlight RAID and press ENTER.
A list of the available RAID levels for the current virtual drive appears.
9. Select a RAID level for the virtual drive and press E
NTER.
10. (Optional) You may also set the logical drive size by highlighting SIZE and then
pressing E
NTER.
The minimum valid virtual drive size is 64 Mbytes. An error will appear if you try to
create a virtual drive that is smaller 64 Mbytes.
By default, all the available space in the array is to the current virtual drive. For
RAID 10 arrays, only one virtual can be defined for the entire array.
11. (Optional) You may change the disks’s default Write Cache and Read Ahead
policies (see Section 4-3: "Setting the Hard Disk Write Cache and Read Ahead
Policies" on page 4-9).
12. When you have finished defining the current virtual drive, select A
CCEPT and press
E
NTER.
13. Configure additional virtual drives on the same array, if desired.
If you have created more than one array, configure a virtual drive on the second
array.
14. Save the configuration when prompted, and press any key to return to the
M
ANAGEMENT menu.
15. Initialize the new virtual drive(s). (See "Initializing Virtual Drives" on page 4-7 for
detailed instructions.)
Creating a Global Hotspare Drive
The MegaRAID BIOS CU enables you to create global hotspare drives (dedicated
hotspare drives are not supported). A hotspare drive can automatically replace a failed
drive in a redundant RAID 1 or RAID 10 array, to protect against data loss.
You can create a hotspare when you are configuring a new storage configuration, as
described in the previous sections.
Adding a Hotspare Drive
To add a hotspare drive to an existing redundant storage configuration, use the following
steps:
1. Select O
BJECTS from the MANAGEMENT menu.
2. Select PHYSICAL DRIVE.
A list of physical drives appears.
WARNING: When you select disk drive for a global hotspare, be sure it is the
same type of drive (either SAS or SATA) as the drives in the arrays that it will
protect. It is recommended that you do not combine SAS and SATA drives in the
same array.
- AOC-USASLP-L8i Add-on Card 1
- User’s Manual 1
- REPRODUCTIVE HARM 2
- Table of Contents 3
- About this Manual 7
- Product Features 7
- Operating Systems Supported 7
- An Important Note to Users 7
- Contacting SuperMicro 8
- Chapter 1 9
- Safety Guidelines 9
- Chapter 2 11
- Chapter 3 15
- 3-3 Flashing Firmware 16
- Chapter 4 19
- Using Easy Configuration 20
- Starting the MegaRAID BIOS CU 20
- CCEPT and press 22
- ANAGEMENT menu 22
- Initializing Virtual Drives 25
- Second Initialization Method 26
- Policies 27
- 4-4 Rebuilding a Drive 28
- 4-5 Hot Plug Support 29
- 4-6 Checking Data Consistency 29
- 4-10 Deleting a Virtual Drive 32
- BJECTS J VIRTUAL DRIVE 33
- ES to confirm 33
- Chapter 5 35
- 5-3 Installing for Windows 36
- 5-4 Installing for Linux 39
- Chapter 6 41
- MegaRAID Window and Menus 41
- PDATE. If you check the 42
- Physical/Logical View Panel 44
- Event Log Panel 45
- Menu Bar 45
- Using Auto Configuration 48
- ONFIGURATION screen: 49
- Using Guided Configuration 50
- UIDED CONFIGURATION screen: 51
- INISH. If 52
- ANUAL CONFIGURATION 53
- EMOVE arrow button 53
- AKE GLOBAL HOTSPARE option 58
- ITH AFFINITY) 58
- 6-7 Deleting a Virtual Disk 60
- Chapter 7 63
- Mirroring Enhanced 63
- 7-2 IM and IME Features 64
- 7-3 IM/IME Description 64
- Logical View Physical View 65
- Metadata Support 66
- Hot Swapping 66
- SMART Support 67
- Hot Spare Disk 67
- Media Verification 67
- Disk Write Caching 67
- NVSRAM Usage 67
- 7-5 Fusion-MPT Support 68
- Creating an IM Volume 69
- Creating an IME Volume 73
- 7-8 Managing Hot Spares 74
- 7-9 Other Configuration Tasks 75
- Activating an Array 76
- Deleting an Array 76
- Locating Drives in a Volume 77
- Selecting a Boot Disk 77
- Chapter 8 79
- Integrated Striping 79
- Fusion-MPT 80
- Controller 80
- 8-5 Fusion-MPT Support 81
- 8-6 IS Configuration Overview 81
- 8-7 Creating IS Volumes 82
- 8-9 Other Configuration Tasks 85
- Locating a Disk in a Volume 86
- Chapter 9 89
- 9-3 CFGGEN Commands 90
- CREATE Command 91
- DEFAULTS Command 93
- DISPLAY Command 93
- FORMAT Command 96
- HOTSPARE Command 97
- STATUS Command 97
- SETOFFLINE Command 98
- SETONLINE Command 99
- Disclaimer 103
Související produkty a manuály pro Řadiče RAID Supermicro AOC-USASLP-L8I
(20 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce