Supermicro SuperChassis 747BTQ-R1K62B Uživatelský manuál

SC747TQ-R1400B SC747TQ-R1620BSC747BTQ-R1K62B USER’S MANUAL 1.0bSC747 CHASSISSeries SUPER®

SC747 Chassis Manual1-21-3 Chassis FeaturesThe SC747 4U high-performance chassis includes the following features:CPUThe SC747 chassis supports single

D-5Appendix D: M35T1 Mobile Rack Specications-D-5 SATA-M35 Backplane SpecicationsTo avoid personal injury and property damage, carefully follow all

SC747 Chassis ManualD-6D-8 Introduction to SATA-M35 The M35T1 mobile rack includes a SATA-M35 Serial ATA (SATA) backplane. This backplane is designed

D-7Appendix D: M35T1 Mobile Rack Specications-D-9 SATA-M35 Front ConnectorsFront Connectors1. 4-pin Power Connectors: JP10 and JP132. ACT IN: JP26

SC747 Chassis ManualD-8 D-10 Front Connectors and Pin DenitionsMain Power4-Pin ConnectorPin# Denition 1 +12V2 and 3Ground4 +5VActi

D-9Appendix D: M35T1 Mobile Rack Specications-D-11 SATA-M35 Front Jumpers and Pin DenitionsJP28JP18JP25Figure D-2: SATA-M35 Front JumpersJumper Set

SC747 Chassis ManualD-10Explanation of JumpersTo modify the operation of the mobile rack, jumpers can be used to choose between optional settings. Jum

D-11Appendix D: M35T1 Mobile Rack Specications-D-12 Rear Connectors and LED IndicatorsThe rear of the mobile rack backplane has SATA connectors and L

SC747 Chassis ManualD-12Rear SAS/SATA ConnectorsRearConnectorReferenceSAS/SATA Drive NumberS-ATA #1 J1 SATA HDD #0 S-ATA #2 J2 SATA HDD #1S-ATA #3

SC747 Chassis ManualD-14D-12 Preparation for InstallationTools RequiredThe following tools are required to install the mobile rack into the chassis:•

D-15Appendix D: M35T1 Mobile Rack Specications-Removing Hard Drive Carriers from the Mobile Rack1. Push the release button on the hard drive carrier

1-3Chapter 1 Introduction1-4 Contacting SupermicroHeadquartersAddress: Super Micro Computer, Inc.980 Rock Ave.San Jose, CA 95131 U.S.A.Tel: +1 (408

SC747 Chassis ManualD-16Figure D-4: Removing Hard Drives From the Mobile Rack2. Use the drive handle to carefully pull the drive from the mobile rack

D-17Appendix D: M35T1 Mobile Rack Specications-Figure D-5: The Hard Drive Carrier and Dummy DriveInstalling a Hard Drive into the Hard Drive Carrier1

SC747 Chassis ManualD-183. Install a new hard drive into the hard drive carrier with the printed circuit board side facing downward so that the mount

D-19Appendix D: M35T1 Mobile Rack Specications-Connecting Cables to the Mobile RackBefore connecting cables the mobile rack, the exhaust fan must be

SC747 Chassis ManualD-20Figure D-9: Removing Mobile Rack Fan2. Pull the exhaust fan off the rear of the mobile rack.Figure D-10: Removing the Bracket

D-21Appendix D: M35T1 Mobile Rack Specications-Figure D-11: Removing Mobile Rack Bracket4. Pull the bracket from the rear of the mobile rack.5. Con

SC747 Chassis ManualD-22Figure D-12: Removing the Mobile Rack Backplane (Optional)Additional Optional Installation InformationIf necessary, before rea

E-1Appendix E: M35TQ Mobile Rack SpecicationsAppendix E M35TQ Mobile Rack SpecicaitonsE-1 OverviewThis manual is written for system integrators, P

SC747 Chassis ManualE-2System Monitoring•Fan failure LED.•Overheat LED indicatior.•Drive activity indicatior.E-3 An Important Note to the UserThe

E-3Appendix E: M35TQ Mobile Rack SpecicationsE-5 Introduction to the SAS-M35TQ BackplaneThe M35TQ mobile rack contains a SAS-M35TQ backplane.

SC747 Chassis Manual1-4Notes

SC747 Chassis ManualE-4E-6 Front ConnectorsREV 1.01SASM35TQRSUPERFront Connectors1. 4-pin Power Connectors: JP10 and JP132. MG9072 Chip3. JTAG Con

E-5Appendix E: M35TQ Mobile Rack Specications E-7 Front Connectors and Pin Denitions2. MG9072 ChipThe MG9072 is an enclosure management chip

SC747 Chassis ManualE-69. Activity LED HeaderThe activity LED header, designated JP26, is used to indicate the activity status of each SAS drive. For

E-7Appendix E: M35TQ Mobile Rack SpecicationsE-8 Front Jumper Locations and Pin DenitionsExplanation of JumpersTo modify the operation of the mobil

SC747 Chassis ManualE-8REV 1.01SASM35TQRSUPERREV 1.01SASM35TQRS UPERJP18JP29*The buzzer sound indicates that a condition requiring immediate attention

E-9Appendix E: M35TQ Mobile Rack SpecicationsFan Jumper SettingsThis mobile rack can utilize up to four fans. To use each fan, you must congure

SC747 Chassis ManualE-10I2C/SGPIO SettingsJumperI2C Setting (Default)SGPIO SettingDescriptionJP33 Pins 2-3 1-2 Controller ID #1JP34 Pins 1-2: ID#0 1-2

E-11Appendix E: M35TQ Mobile Rack SpecicationsE-9 Rear Connectors and LED IndicatorsThe rear of the mobile rack backplane has SAS/SATA connectors an

SC747 Chassis ManualE-12Rear SAS/SATA ConnectorsRearConnectorSAS/SATA Drive NumberSAS #0 SAS/SATA HHD #0 SAS #1 SAS/SATA HHD #1SAS #2 SAS/SATA HHD

E-13Appendix E: M35TQ Mobile Rack SpecicationsE-10 Preparing for InstallationTools RequiredThe following tools are required to install the mobile ra

2-1Chapter 2: Warning Statements for AC SystemsChapter 2 Standardized Warning Statements for AC Systems2-1 About Standardized Warning StatementsThe

SC747 Chassis ManualE-14Removing Hard Drives from the Mobile Rack1. Push the release button on the hard drive, which will extend the drive handle2.

E-15Appendix E: M35TQ Mobile Rack SpecicationsFigure E-8: Chassis Drive CarrierInstalling a Hard Drive into the Hard Drive Carrier1. Remove the two

SC747 Chassis ManualE-163. Install a new drive into the carrier with the printed circuit board side facing downward so that the mounting holes in the

E-17Appendix E: M35TQ Mobile Rack SpecicationsConnecting Cables to the Mobile RackBefore connecting cables the mobile rack, the exhaust fan must be r

SC747 Chassis ManualE-18Figure E-12: Removing Mobile Rack Fan2. Pull the exhaust fan off the rear of the mobile rack.12

E-19Appendix E: M35TQ Mobile Rack SpecicationsFigure E-13: Removing Mobile Rack Fan3. Remove the bracket screw from the side of the mobile rack.4.

SC747 Chassis ManualE-20Figure E-14: Removing Mobile Rack Backplane (Optional)Additional Optional Installation InformationIf necessary, before reassem

E-21Appendix E: M35TQ Mobile Rack SpecicationsNotes

SC747 Chassis ManualE-22Disclaimer (cont.)The products sold by Supermicro are not intended for and will not be used in life sup-port systems, medical

2-2SC216 Chassis ManualWarnung WICHTIGE SICHERHEITSHINWEISEDieses Warnsymbol bedeutet Gefahr. Sie benden sich in einer Situation, die zu Ve

2-3Warning Statements for AC Systems안전을 위한 주의사항경고!이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수 있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와 관련된 위험요소들을 확

2-4SC216 Chassis ManualInstallation Instructions Warning!Read the installation instructions before connecting the system to the power source.WarnungVo

2-5Chapter 2: Warning Statements for AC SystemsCircuit Breaker Warning!This product relies on the building's installation for short-circuit (over

2-6SC216 Chassis ManualPower Disconnection Warning 電源切断の警告システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセスするには、システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り外す必要がありま

2-7Chapter 2: Warning Statements for AC Systems¡Advertencia! El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico qu

SC747 Chassis ManualiiManual Revision 1.0b Release Date: December 26, 2012The information in this User’s Manual has been carefully reviewed and

2-8SC216 Chassis ManualEquipment Installation機器の設置トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可されています。 Warning!Only trained and qualied personnel should be

2-9Chapter 2: Warning Statements for AC Systemsアクセス制限区域このユニットは、アクセス制限区域に設置されることを想定しています。アクセス制限区域は、特別なツール、鍵と錠前、その他のセキュリティの手段を用いてのみ出入りが可能です。 Warning!Thi

2-10SC216 Chassis ManualBattery Handling Warning!There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only wit

2-11Chapter 2: Warning Statements for AC SystemsWarnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur

2-12SC216 Chassis ManualWarnung Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein trom zugeführt wird, müss

2-13Chapter 2: Warning Statements for AC SystemsBackplane Voltageバックプレーンの電圧システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。修理する際には注意ください。警告当系统正在进行时，背板上有很危险的电压或能

2-14SC216 Chassis ManualComply with Local and National Electrical Codes Warning!Installation of the equipment must comply with local and national elec

2-15Chapter 2: Warning Statements for AC SystemsProduct Disposal Warning!Ultimate disposal of this product should be handled according to all national

2-16SC216 Chassis ManualWaarschuwing De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming met alle nationale wetten en

2-17Chapter 2: Warning Statements for AC SystemsWarnungDie Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis genommen wird. Halt

iiiPrefacePrefaceAbout This ManualThis manual is written for professional system integrators and PC technicians. It provides information for the insta

2-18SC216 Chassis Manual Warning!When installing the product, use the provided or designated connection cables, power cables and AC adaptors. Using an

2-19Chapter 2: Warning Statements for AC SystemsAttention Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné

2-20SC216 Chassis ManualNotes

3-1Chapter 3 Chassis ComponentsChapter 3 Chassis Components3-1 OverviewThis chapter describes the most common components included with your chassis.

SC747 Chassis Manual3-2Power SupplySC747 chassis model includes (93%+) Gold Level 1400W redundant (1+1) power supplies rated at 1400 Watts or redundan

4-1Chapter 4 System InterfaceChapter 4 System Interface4-1 OverviewThere are several LEDs on the control panel as well as others on the drive carrie

SC747 Chassis Manual4-24-2 Control Panel ButtonsThere are two push-buttons located on the front of the chassis, a power on/off button and a reset but

4-3Chapter 4 System Interface•NIC2: Indicates network activity on GLAN2 when ashing.•Overheat/Fan Fail: When this LED ashes it indicates a

SC747 Chassis Manual4-44-4 Drive Carrier LEDsYour chassis uses SAS/SATA drives.SAS/SATA DrivesEach SAS/SATA drive carrier has two LEDs.•Green: Each

5-1Chapter 5 Chassis Setup and MaintenanceChapter 5 Chassis Setup and Maintenance5-1 OverviewThis chapter covers the steps required to install compo

SC747 Chassis ManualivManual OrganizationChapter 1 IntroductionThe rst chapter provides an overview of the main components included with this chassis

SC747 Chassis Manual5-25-3 Chassis CoversThe SC747 chassis has three covers, the main cover, the top cover and the front cover. This section of the m

5-3Chapter 5 Chassis Setup and MaintenanceRemoving the Main CoverRemoving the Chassis Main Cover1. Power down the system and remove the power cords f

SC747 Chassis Manual5-4Opening the Front CoverThe front cover houses up to eight hot-swappable hard drives. The cover can be locked to prevent unautho

5-5Chapter 5 Chassis Setup and Maintenance5-4 Conguring the the Storage Module Storage ModuleTower or Rack CongurationThe SC747 chassis is shipped

SC747 Chassis Manual5-6Rotating the Storage Module for Rack Mounting1. Power down the system, remove the power cords from the rear of the power suppl

5-7Chapter 5 Chassis Setup and MaintenanceInstalling Drives in the Storage ModuleThe storage module includes three full-sized drive bays and the front

SC747 Chassis Manual5-8Drive CarrierRelease TabsUse the following instructions to add up to three peripheral drives (DVD-ROM, CD-ROM, etc.) to the dri

5-9Chapter 5 Chassis Setup and Maintenance4. Remove the drive carrier rails from the drive carrier. To do this, you must remove two screws from each s

SC747 Chassis Manual5-10Drive CarrierRelease TabsAdding Hard Drives to the Drive Carriers1. Power down the server, unplug the power cords from the re

5-11Chapter 5 Chassis Setup and Maintenance3. Push the drive carrier toward the front of the chassis.4. Place the hard drive into the drive carrier.

vPrefaceAppendicesThis section lists compatible cables, power supply specications, and compatible backplanes. Not all compatible backplanes are liste

SC747 Chassis Manual5-12Drive CarrierRelease TabsAdding Five Hard Drives Using a Supermicro Mobile RackThe SC747 chassis supports a CSE-M35T-1/CS

5-13Chapter 5 Chassis Setup and MaintenanceMobile RackHard DriveRails3. Pull the rst drive release tab and push the drive carrier toward the front o

SC747 Chassis Manual5-14Installing Hard Drives into the ChassisThe drives are mounted in drive carriers to simplify their installation and removal fro

5-15Chapter 5 Chassis Setup and Maintenance6. Secure the hard drive to the carrier using four screws.7. Insert the hard drive into the chassis. To do

SC747 Chassis Manual5-16I/O Shield5-6 Installing the MotherboardI/O Slot Shield InstallationThe I/O shield holds the motherboard ports in place. Inst

5-17Chapter 5 Chassis Setup and MaintenancePermanent and Optional StandoffsStandoffs prevent short circuits by creating space between the motherboard

SC747 Chassis Manual5-18Installing the MotherboardInstalling the Motherboard into the Chassis1. Review the documentation that came with your motherbo

5-19Chapter 5 Chassis Setup and MaintenanceInstalling the Active HeatsinkFigure 5-20: Installing the Active HeatsinkInstallation of the active heatsin

SC747 Chassis Manual5-20Power Supply ConnectionsConnect each of the following cables, as required, by your motherboard manufac-turer. In some instance

5-21Chapter 5 Chassis Setup and MaintenanceConguring the Expansion SlotsAfter the motherboard installation, install expansion cards in the chassis.In

SC747 Chassis ManualviTable of ContentsPreface ...

SC747 Chassis Manual5-224. Pull the release tab upward.5. Remove the screw holding the bracket in place and pull the bracket from the chassis.6. In

5-23Chapter 5 Chassis Setup and MaintenanceInstalling Double-Width Graphics CardsThe SC747 chassis is designed to support up to four double-width, hig

SC747 Chassis Manual5-24Figure 5-24: Closing the Graphics Card Holder3. Place the tabs of the MCP-290-74702-0N graphics card holder into the slots on

5-25Chapter 5 Chassis Setup and MaintenanceSix heavy-duty fans provide cooling for the chassis. Four system fans are located in the mid-section of the

SC747 Chassis Manual5-26Rear Fan Release TabFigure 5-26: Rear Exhaust FansReplacing Rear Exhaust FansReplacing the Rear Exhaust Fan1. Determine which

5-27Chapter 5 Chassis Setup and MaintenanceFigure 5-27: PCI Slot ModicationAdding Optional External Rear Fans (BTQ Model Only)SC747BTQ chassis models

SC747 Chassis Manual5-284. Place two of the loose, metal bracket mounting pins into the holes at the base of the PCI slots in the position where the

5-29Chapter 5 Chassis Setup and Maintenance10. Route the wiring through the open latch slot and into the chassis. 11. For cosmetic purposes the plasti

SC747 Chassis Manual5-30Release TabFigure 31: Power Supply Release Button 5-8 Power Supply The SC747 chassis is equipped with 1400W or 1620W (redunda

6-1Chapter 6 Rack InstallationChapter 6 Rack Installation6-1 OverviewThis chapter provides instuctions for installing your system into a rack enviro

viiPrefacePower Supply ... 3-23-3 Where to get Replace

SC747 Chassis Manual6-2Rack Precautions•Ensure that the leveling jacks on the bottom of the rack are fully extended to the oor with the full weight

6-3Chapter 6 Rack Installationenvironment compatible with the manufacturer’s maximum rated ambient tempera-ture (TMRA).Reduced AirowEquipment should

SC747 Chassis Manual6-46-4 Installing the Chassis onto a RackThis section provides information on installing the SC747 chassis into a rack unit with

6-5Chapter 6 Rack InstallationRemoving the Chassis Top Cover1. Locate the chassis cover lock (blue lever) at the rear of the chassis cover.2. Slide

SC747 Chassis Manual6-6Figure 6-2: Identifying the Inner Rails and Chassis HandlesChassis HandleInner RailsIdentifying the Sections of the Rack Rails

6-7Chapter 6 Rack InstallationFigure 6-3: Installing the Inner Rack Rails Installing the Chassis Handles and Inner RailsInstalling the Inner Rails1.

SC747 Chassis Manual6-8Installing the Outer Rails to the RackInstalling the Outer Rails1. Attach the rear rail to the middle rail. 2. Adjust both to

6-9Chapter 6 Rack InstallationFigure 6-5: Installing the Rack RailsInstalling the Chassis into a RackInstalling the Chassis1. Conrm that chassis incl

SC747 Chassis Manual6-106-5 Tower Mounting InstructionsThe SC747 chassis is shipped with the chassis cover and feet pre-installed. To use the chassis

6-11Chapter 6 Rack InstallationInstalling Feet on the ChassisInstalling the Chassis Feet1. Place the chassis foot in the foot receptacle and slide th

SC747 Chassis ManualviiiRack Precautions ... 6-2Rack Mounting

SC747 Chassis Manual6-12Notes

A-1Appendix A Chassis CablesAppendix A SC747 Chassis CablesA-1 OverviewThis appendix lists supported cables for your chassis system. It only include

SC747 Chassis ManualA-2Description: This cable has one SFF-8484 (32-pin) connector on one end and four SAS connectors (7 pins each) at the

A-3Appendix A Chassis CablesExtending Power CablesAlthough Supermicro chassis are designed with to be efcient and cost-effective, some compatib

SC747 Chassis ManualA-4Notes

B-1Appendix B: Power Supply Specications Appendix B SC747 Power Supply SpecicationsThis appendix lists power supply specications for your chassis

SC747 Chassis ManualB-2Notes

C-1Appendix C SAS-747TQ Backplane Specitications Appendix C SAS-747TQ Backplane SpecicationsTo avoid personal injury and property damage, carefully

C-2SC747 Chassis ManualC-3 An Important Note to UsersAll images and layouts shown in this user's guide are based upon the latest revision availa

C-3Appendix C SAS-747TQ Backplane Specitications DESIGNED IN USA1JP187J87J77J67J57J167J147J127J10BZ1+41JP6541JP6041JP5641JP131 4JP101 4R99R6R324R154R3

Chapter 1 Introduction1-1 OverviewSupermicro’s SC747 4U chassis features a unique and highly-optimized design. The chassis is equipped with a high-e

C-4SC747 Chassis ManualC-6 Front Connector and Pin Denitions4. MG9072 ChipThe MG9072 is an enclosure management chip that supports the SES-2 co

C-5Appendix C SAS-747TQ Backplane Specitications BackplaneMain Power4-Pin ConnectorPin# Denition 1 +12V2 and 3 Ground4 +5V5. Backplane

C-6SC747 Chassis ManualDESIGNED IN USA1JP187J87J77J67J57J167J147J127J10BZ1+41JP6541JP6041JP5641JP131 4JP101 4R99R6R324R154R325CAD47CAD45CAD3CAD54CAD53

C-7Appendix C SAS-747TQ Backplane Specitications Socket SettingsSocket Socket Setting NoteJP18Connected to the front panelBuzzer reset*Press once to d

C-8SC747 Chassis ManualI2C and SGPIO Modes and Jumper SettingsThis backplane can utilize I2C or SGPIO. SGPIO is the default mode and can be used witho

C-9Appendix C SAS-747TQ Backplane Specitications DESIGNED IN USA1JP187J87J77J67J57J167J147J127J10BZ1+41JP6541JP6041JP5641JP131 4JP101 4R99R6R324R154R3

C-10SC747 Chassis ManualC-9 Rear Connectors and LED IndicatorsRear SAS/SATA ConnectorsRearConnectorSAS Drive Number#0 SAS/SATA HDD #0 #1 SAS/SATA H

D-1Appendix D: M35T1 Mobile Rack Specications-Appendix D M35T1 Mobile Rack SpecicationsD-1 OverviewThis manual is written for system integrators,

SC747 Chassis ManualD-2System Monitoring•Fan failure LED•Overheat LED indicatior•Drive activity indicatiorD-3 An Important Note to the UserThe pic

D-3Appendix D: M35T1 Mobile Rack Specications-D-4 Returning Merchandise for ServiceA receipt or copy of your invoice marked with the date of purchas